| Voir le sujet précédent :: Voir le sujet suivant |
| Auteur |
Message |
kansalliskala
 Inscrit le: 19 Juil 2007 Messages: 5122 Localisation: Southern Finland countryside
Expire: 2016-12-30
|
 Posté: Jeu Oct 16, 2008 8:39 am Sujet du message: Pentax K lens -> m42 mount conversion |
|
 Posté: Jeu Oct 16, 2008 8:39 am Sujet du message: Pentax K lens -> m42 mount conversion |
|
|
kansalliskala wrote:
Anyone done that? Register distance is the same but are there parts that can't be removed?
Do you think we should have "avant-garde" area for all kinds of experiments?  _________________ MF: Kodak DCS SLR/c; Samsung NX10; OM-10; Canon T50
Zuiko 28/3.5, Distagon 35/2.8; Yashica ML 50/2;
Zuiko 50/1.4; S-M-C 120/2.8; Zuiko 135/3.5; 200/5;
Tamron AD1 135/2.8, Soligor 180/3.5; Tamron AD1 300/5.6
Tamron zooms: 01A, Z-210
Yashicaflex C; Київ 4 + Юпитер 8, 11; Polaroid 100; Olympus XA; Yashica T3
Museum stuff: Certo-Phot; Tele-Edixon 135; Polaris 90-190; Asahi Bellows; Ixus IIs
Projects: Agfa Isolette III (no shutter), Canon AE-1D (no sensor),
Nikon D80 (dead), The "Peace Camera"
AF: Canon, Tokina, Sigma Video: JVC GZ-MG275E
Dernière modification par kansalliskala le Jeu Oct 16, 2008 11:09 am ; modifié 1 fois au total |
|
| Haut de page |
|
 |
Xpres
 Inscrit le: 11 Déc 2007 Messages: 964 Localisation: UK
Expire: 2014-10-28
|
 Posté: Jeu Oct 16, 2008 10:16 am Sujet du message: |
|
 Posté: Jeu Oct 16, 2008 10:16 am Sujet du message: |
|
|
Xpres wrote:
You could just use an adapter.... _________________ Film... and sometimes SD14, 5D2 and some other suff! |
|
| Haut de page |
|
 |
kansalliskala
 Inscrit le: 19 Juil 2007 Messages: 5122 Localisation: Southern Finland countryside
Expire: 2016-12-30
|
 Posté: Jeu Oct 16, 2008 11:09 am Sujet du message: |
|
 Posté: Jeu Oct 16, 2008 11:09 am Sujet du message: |
|
|
kansalliskala wrote:
Sorry, I was vague.
I was thinking that I take Pentax K-lens, grind the back off and put m42 thread there. The obvious difficulty is if the aperture mechanism springs and cogs fly to different directions during operation. _________________ MF: Kodak DCS SLR/c; Samsung NX10; OM-10; Canon T50
Zuiko 28/3.5, Distagon 35/2.8; Yashica ML 50/2;
Zuiko 50/1.4; S-M-C 120/2.8; Zuiko 135/3.5; 200/5;
Tamron AD1 135/2.8, Soligor 180/3.5; Tamron AD1 300/5.6
Tamron zooms: 01A, Z-210
Yashicaflex C; Київ 4 + Юпитер 8, 11; Polaroid 100; Olympus XA; Yashica T3
Museum stuff: Certo-Phot; Tele-Edixon 135; Polaris 90-190; Asahi Bellows; Ixus IIs
Projects: Agfa Isolette III (no shutter), Canon AE-1D (no sensor),
Nikon D80 (dead), The "Peace Camera"
AF: Canon, Tokina, Sigma Video: JVC GZ-MG275E |
|
| Haut de page |
|
 |
peterqd
 Inscrit le: 28 Fév 2007 Messages: 7449 Localisation: near High Wycombe, UK
Expire: 2014-01-04
|
 Posté: Jeu Oct 16, 2008 12:01 pm Sujet du message: |
|
 Posté: Jeu Oct 16, 2008 12:01 pm Sujet du message: |
|
|
peterqd wrote:
Hi, the aperture arm broke off from my smc Pentax-M 1.7/50 and I took off the chrome backplate to try to fix it. I think it would be perfectly possibly to replace the backplate with an old M42 plate drilled to fit the screwholes. The projecting shield round the rear element is fitted to the backplate so this would disappear.
As for the aperture control, the control ring has a groove on the inside that fits over an arm connected to the blades, so this has to stay. This arm is L-shaped and has a part pointing back towards the camera which goes through a slot in the backplate, so it would be necessary to file this down to clear the underside of the plate. There is another longer arm (which broke off my lens) which would need to be removed. This is rivetted to on a plate inside the lens and could be drilled out (if it won't break off like mine!).
Do you need any pics? _________________ Peter - Moderator |
|
| Haut de page |
|
 |
LucisPictor
 Inscrit le: 26 Fév 2007 Messages: 17633 Localisation: Oberhessen, Germany / Maidstone ('95-'96)
Expire: 2013-12-03
|
 Posté: Jeu Oct 16, 2008 12:41 pm Sujet du message: |
|
 Posté: Jeu Oct 16, 2008 12:41 pm Sujet du message: |
|
|
LucisPictor wrote:
| Xpres a écrit: |
| You could just use an adapter.... |
I don't think that there is an adapter to turn a PK-lens into an M42-lens, just the other way around. _________________ Personal forum activity on pause every now and again (due to job obligations)!
Carsten, former Moderator
Things ON SALE
Carsten = "KAPCTEH" = "Karusutenu" | T-shirt?.........................My photos from Emilia: http://www.schouler.net/emilia/emilia2011.html
My gear: http://retrocameracs.wordpress.com/ausrustung/
Old list: http://forum.mflenses.com/viewtopic.php?t=65 (Not up-to-date, sorry!) | http://www.lucispictor.de | http://www.alensaweek.wordpress.com |
http://www.retrocamera.de |
|
| Haut de page |
|
 |
Xpres
 Inscrit le: 11 Déc 2007 Messages: 964 Localisation: UK
Expire: 2014-10-28
|
 Posté: Jeu Oct 16, 2008 1:15 pm Sujet du message: |
|
 Posté: Jeu Oct 16, 2008 1:15 pm Sujet du message: |
|
|
Xpres wrote:
| LucisPictor a écrit: |
| Xpres a écrit: |
| You could just use an adapter.... |
I don't think that there is an adapter to turn a PK-lens into an M42-lens, just the other way around. |
You're right... the original post is clear now, I misunderstood. _________________ Film... and sometimes SD14, 5D2 and some other suff! |
|
| Haut de page |
|
 |
kansalliskala
 Inscrit le: 19 Juil 2007 Messages: 5122 Localisation: Southern Finland countryside
Expire: 2016-12-30
|
 Posté: Jeu Oct 16, 2008 1:26 pm Sujet du message: |
|
 Posté: Jeu Oct 16, 2008 1:26 pm Sujet du message: |
|
|
kansalliskala wrote:
| peterqd a écrit: |
As for the aperture control, the control ring has a groove on the inside that fits over an arm connected to the blades, so this has to stay. This arm is L-shaped and has a part pointing back towards the camera which goes through a slot in the backplate, so it would be necessary to file this down to clear the underside of the plate. |
Is this the "auto" connection that shuts the aperture by some spring mechanism or does it actually move the blades?
Do you have a picture with the backplate off?
Thanks! _________________ MF: Kodak DCS SLR/c; Samsung NX10; OM-10; Canon T50
Zuiko 28/3.5, Distagon 35/2.8; Yashica ML 50/2;
Zuiko 50/1.4; S-M-C 120/2.8; Zuiko 135/3.5; 200/5;
Tamron AD1 135/2.8, Soligor 180/3.5; Tamron AD1 300/5.6
Tamron zooms: 01A, Z-210
Yashicaflex C; Київ 4 + Юпитер 8, 11; Polaroid 100; Olympus XA; Yashica T3
Museum stuff: Certo-Phot; Tele-Edixon 135; Polaris 90-190; Asahi Bellows; Ixus IIs
Projects: Agfa Isolette III (no shutter), Canon AE-1D (no sensor),
Nikon D80 (dead), The "Peace Camera"
AF: Canon, Tokina, Sigma Video: JVC GZ-MG275E |
|
| Haut de page |
|
 |
peterqd
 Inscrit le: 28 Fév 2007 Messages: 7449 Localisation: near High Wycombe, UK
Expire: 2014-01-04
|
 Posté: Jeu Oct 16, 2008 2:05 pm Sujet du message: |
|
 Posté: Jeu Oct 16, 2008 2:05 pm Sujet du message: |
|
|
peterqd wrote:
| kansalliskala a écrit: |
| peterqd a écrit: |
As for the aperture control, the control ring has a groove on the inside that fits over an arm connected to the blades, so this has to stay. This arm is L-shaped and has a part pointing back towards the camera which goes through a slot in the backplate, so it would be necessary to file this down to clear the underside of the plate. |
Is this the "auto" connection that shuts the aperture by some spring mechanism or does it actually move the blades?
Do you have a picture with the backplate off?
Thanks! |
The auto feature of PK lenses works in reverse to M42 lenses. Instead of the aperture blades being held open by a spring, as on an M42 lens, on a PK lens the spring tries to keep them closed down. When the lens is mounted on the camera, the longer arm (the one that broke off my lens) holds the aperture open against the spring until the shutter is fired. But when the lens is not mounted and the arm is free, the spring closes the aperture down to the f-setting of the dia ring. You can try this by hand. Therefore the lens would function OK without the long arm, but in stop-down mode only.
The other arm is more difficult to see. It's inside the long slot on the opposite side of the rear element to the long arm. It doesn't project beyond the plate, but it will prevent the new backplate from seating properly unless you shorten it or cut a new slot. This is the L-shaped one I described and the other end of it sits in a slot on the inside of the dia ring. It's not directly connected to the blades, but acts as a stop for the spring, and without it the spring would close the aperture right down. That's why I said it has to stay.
I'll do some pics for you shortly, backplate removed. I bought a direct replacement for this lens but it had fungus, so I swapped the glass over. The pics will be of the old body with the fungus glass.  _________________ Peter - Moderator |
|
| Haut de page |
|
 |
peterqd
 Inscrit le: 28 Fév 2007 Messages: 7449 Localisation: near High Wycombe, UK
Expire: 2014-01-04
|
 Posté: Jeu Oct 16, 2008 2:37 pm Sujet du message: |
|
 Posté: Jeu Oct 16, 2008 2:37 pm Sujet du message: |
|
|
peterqd wrote:
OK, here is the PK mount before disassembly:
The chrome backplate is fixed with 5 crosshead screws and just lifts off. Note that the black insert surrounding the rear element, including the projecting shield, is fixed to the backplate:
With the plate removed you can see the shorter arm on the left, connected to the dia ring. This needs to be shortened. The longer arm (see the first pic) would normally be mounted by the two stubs of rivets you can see on the right hand side. On this lens the arm has broken off.
 _________________ Peter - Moderator |
|
| Haut de page |
|
 |
kansalliskala
 Inscrit le: 19 Juil 2007 Messages: 5122 Localisation: Southern Finland countryside
Expire: 2016-12-30
|
 Posté: Jeu Oct 16, 2008 5:03 pm Sujet du message: |
|
 Posté: Jeu Oct 16, 2008 5:03 pm Sujet du message: |
|
|
kansalliskala wrote:
Bigger problem might be the diameter of back lenses - that is one reason why they switched to bayonets. _________________ MF: Kodak DCS SLR/c; Samsung NX10; OM-10; Canon T50
Zuiko 28/3.5, Distagon 35/2.8; Yashica ML 50/2;
Zuiko 50/1.4; S-M-C 120/2.8; Zuiko 135/3.5; 200/5;
Tamron AD1 135/2.8, Soligor 180/3.5; Tamron AD1 300/5.6
Tamron zooms: 01A, Z-210
Yashicaflex C; Київ 4 + Юпитер 8, 11; Polaroid 100; Olympus XA; Yashica T3
Museum stuff: Certo-Phot; Tele-Edixon 135; Polaris 90-190; Asahi Bellows; Ixus IIs
Projects: Agfa Isolette III (no shutter), Canon AE-1D (no sensor),
Nikon D80 (dead), The "Peace Camera"
AF: Canon, Tokina, Sigma Video: JVC GZ-MG275E |
|
| Haut de page |
|
 |
peterqd
 Inscrit le: 28 Fév 2007 Messages: 7449 Localisation: near High Wycombe, UK
Expire: 2014-01-04
|
 Posté: Jeu Oct 16, 2008 7:26 pm Sujet du message: |
|
 Posté: Jeu Oct 16, 2008 7:26 pm Sujet du message: |
|
|
peterqd wrote:
The outside diameter of the rear lens in the picture is 34.1mm. The removable M42 mount on a Jupiter-37A has 37.2mm internal diameter _________________ Peter - Moderator |
|
| Haut de page |
|
 |
ryan s
 Inscrit le: 26 Sep 2008 Messages: 384 Localisation: Madison, WI
|
 Posté: Ven Oct 17, 2008 6:31 am Sujet du message: |
|
 Posté: Ven Oct 17, 2008 6:31 am Sujet du message: |
|
|
ryan s wrote:
Just curious...what lenses are you looking at in K mount that you can't find in native M42? _________________ Pentax Bodies: K10D + D-BG2 | MX |
M: Zenitar 16/2.8 | 28/2.8 | 50/1.7 | M39: Mir-1 GP 37/2.8 M42: Vivitar 28/2.5 AD2: Tamron SP Macro 90/2.5 |
|
| Haut de page |
|
 |
kansalliskala
 Inscrit le: 19 Juil 2007 Messages: 5122 Localisation: Southern Finland countryside
Expire: 2016-12-30
|
 Posté: Ven Oct 17, 2008 9:35 am Sujet du message: |
|
 Posté: Ven Oct 17, 2008 9:35 am Sujet du message: |
|
|
kansalliskala wrote:
That is not the point. My idea is more star-trek-like-assignmet "to adapt any lens to any kind of mount".  _________________ MF: Kodak DCS SLR/c; Samsung NX10; OM-10; Canon T50
Zuiko 28/3.5, Distagon 35/2.8; Yashica ML 50/2;
Zuiko 50/1.4; S-M-C 120/2.8; Zuiko 135/3.5; 200/5;
Tamron AD1 135/2.8, Soligor 180/3.5; Tamron AD1 300/5.6
Tamron zooms: 01A, Z-210
Yashicaflex C; Київ 4 + Юпитер 8, 11; Polaroid 100; Olympus XA; Yashica T3
Museum stuff: Certo-Phot; Tele-Edixon 135; Polaris 90-190; Asahi Bellows; Ixus IIs
Projects: Agfa Isolette III (no shutter), Canon AE-1D (no sensor),
Nikon D80 (dead), The "Peace Camera"
AF: Canon, Tokina, Sigma Video: JVC GZ-MG275E |
|
| Haut de page |
|
 |
peterqd
 Inscrit le: 28 Fév 2007 Messages: 7449 Localisation: near High Wycombe, UK
Expire: 2014-01-04
|
 Posté: Ven Oct 17, 2008 5:10 pm Sujet du message: |
|
 Posté: Ven Oct 17, 2008 5:10 pm Sujet du message: |
|
|
peterqd wrote:
| kansalliskala a écrit: |
That is not the point. My idea is more star-trek-like-assignmet "to adapt any lens to any kind of mount".  |
More like "Mission Impossible"! Were the pics helpful? _________________ Peter - Moderator |
|
| Haut de page |
|
 |
kansalliskala
 Inscrit le: 19 Juil 2007 Messages: 5122 Localisation: Southern Finland countryside
Expire: 2016-12-30
|
 Posté: Sam Oct 18, 2008 9:52 am Sujet du message: |
|
 Posté: Sam Oct 18, 2008 9:52 am Sujet du message: |
|
|
kansalliskala wrote:
Yes, thank you, they were most informative!
Actually they seemed the task more possible than I first thought.  _________________ MF: Kodak DCS SLR/c; Samsung NX10; OM-10; Canon T50
Zuiko 28/3.5, Distagon 35/2.8; Yashica ML 50/2;
Zuiko 50/1.4; S-M-C 120/2.8; Zuiko 135/3.5; 200/5;
Tamron AD1 135/2.8, Soligor 180/3.5; Tamron AD1 300/5.6
Tamron zooms: 01A, Z-210
Yashicaflex C; Київ 4 + Юпитер 8, 11; Polaroid 100; Olympus XA; Yashica T3
Museum stuff: Certo-Phot; Tele-Edixon 135; Polaris 90-190; Asahi Bellows; Ixus IIs
Projects: Agfa Isolette III (no shutter), Canon AE-1D (no sensor),
Nikon D80 (dead), The "Peace Camera"
AF: Canon, Tokina, Sigma Video: JVC GZ-MG275E |
|
| Haut de page |
|
 |
Flor27
 Inscrit le: 13 Sep 2007 Messages: 1195 Localisation: Paris, France
|
 Posté: Ven Oct 31, 2008 3:26 pm Sujet du message: |
|
 Posté: Ven Oct 31, 2008 3:26 pm Sujet du message: |
|
|
Flor27 wrote:
| kansalliskala a écrit: |
Yes, thank you, they were most informative!
Actually they seemed the task more possible than I first thought.  |
I know none Pentax K lens that need the mount to work. I mean the aperture ring can still open or close the iris blades at the right values even if the metal bayonet mount is removed. This is not the same deal with third party PK lenses.
Dismantled SMC Pentax-M lenses so far : 28/2.8; 28/3.5; 35/2.0; 40/2.8; 50/1.7; 135/3/5 _________________ Switching from M42 to Minolta MD & Contax/Yashica |
|
| Haut de page |
|
 |
kansalliskala
 Inscrit le: 19 Juil 2007 Messages: 5122 Localisation: Southern Finland countryside
Expire: 2016-12-30
|
 Posté: Jeu Nov 06, 2008 9:24 am Sujet du message: |
|
 Posté: Jeu Nov 06, 2008 9:24 am Sujet du message: |
|
|
kansalliskala wrote:
Third party lens(es) are even easier. Here is Makinon 35-70. The whole mount and all the levers were attached to the same module. Obviously because one can use the same lens for several mounts.
Now the task is just too simple, just grind and drill the donor mount. But I don't know any more if I want to do that. The lens itself is crap and there is a hair or scratch inside so there is no great practical use? First I thought I could use it as some sort of "emergency" lens with Zenit in environments where I don't want to go with my russian lenses such as rock climbing and sportsbars.
It might be more interesting to just disassemble it to see how zooms work? _________________ MF: Kodak DCS SLR/c; Samsung NX10; OM-10; Canon T50
Zuiko 28/3.5, Distagon 35/2.8; Yashica ML 50/2;
Zuiko 50/1.4; S-M-C 120/2.8; Zuiko 135/3.5; 200/5;
Tamron AD1 135/2.8, Soligor 180/3.5; Tamron AD1 300/5.6
Tamron zooms: 01A, Z-210
Yashicaflex C; Київ 4 + Юпитер 8, 11; Polaroid 100; Olympus XA; Yashica T3
Museum stuff: Certo-Phot; Tele-Edixon 135; Polaris 90-190; Asahi Bellows; Ixus IIs
Projects: Agfa Isolette III (no shutter), Canon AE-1D (no sensor),
Nikon D80 (dead), The "Peace Camera"
AF: Canon, Tokina, Sigma Video: JVC GZ-MG275E |
|
| Haut de page |
|
 |
|
|
|
Vous ne pouvez pas publier de nouveaux sujets dans ce forum Vous ne pouvez pas répondre aux sujets de ce forum Vous ne pouvez pas modifier vos messages dans ce forum Vous ne pouvez pas supprimer vos messages dans ce forum Vous ne pouvez pas voter dans les sondages de ce forum
|