| Voir le sujet précédent :: Voir le sujet suivant |
| Auteur |
Message |
stevemark
 Inscrit le: 29 Avr 2011 Messages: 5509 Localisation: Switzerland
|
 Posté: Mer Avr 01, 2026 10:48 pm Sujet du message: REPAIR: Pentax A 1.4/50mm cleaning (lots of fungus) |
|
 Posté: Mer Avr 01, 2026 10:48 pm Sujet du message: REPAIR: Pentax A 1.4/50mm cleaning (lots of fungus) |
|
|
stevemark wrote:
There's not much information about servicing the Pentax A 1.4/50mm in the net. Here's a detailed step-by-step guide about dismantling and cleaning the Pentax A 1.4/50mm and all its six lens elements (five single lenses and one doublet).
Recently I got a rather nice looking Pentax A 1.4/50mm which was sold "as is", obviously with "some" fungus. The lens would - I assumed - fit my Pentax LX rather nicely. Up to now I had only the Pentax A 2/50mm and the Pentax A 2.8/50mm Macro normal lenses; and an f1.4 normal lens would look nice, for sure!
When I got the lens it was obvious that there was more than one surface contaminated with fungus. In addition the focusing felt quite "dry" and uneven. The lens itself didn't look bad, and I assumed cleaning it would be rather quick. I was wrong. _________________ www.artaphot.ch
Dernière modification par stevemark le Ven Sep 18, 2026 11:47 pm ; modifié 1 fois au total |
|
| Haut de page |
|
 |
stevemark
 Inscrit le: 29 Avr 2011 Messages: 5509 Localisation: Switzerland
|
|
| Haut de page |
|
 |
stevemark
 Inscrit le: 29 Avr 2011 Messages: 5509 Localisation: Switzerland
|
 Posté: Jeu Avr 02, 2026 7:36 pm Sujet du message: |
|
 Posté: Jeu Avr 02, 2026 7:36 pm Sujet du message: |
|
|
stevemark wrote:
PART II: DISMANTLING THE LENS BARREL
Remove the five bayonet screws:
CAREFULLY remove the bayonet mount:
ATTENTION: there are two small parts which can be lost easily (arrow)!
The small golden spring (less than 1mm in diameter) an the silver metallic knob (less than 2mm) are part of the signal transferring mechanism for the "Auto Aperture [A]" setting:
Since we can't dismantle the lens any further from the back side, we have to go back toi the front side.
Remove these three screws:
Remove the corresponding plastic ring including the metal part which serves as a base for the screws:
Now the aperture mechanism can be removed:
Luckily it comes out as one part - nicely done by the Pentax engineers! It can be dsimantled further if necessary, but in my case everything was perfect and so I simply put it aside:
Now the foremost doublet of the rear lens group can be removed:
Next we can take off the aperture ring. I took me a while until I found out that i can be removed only if the aperture is set to f5.6!
Aperture ring removed:
Now we can take out these screws (three of the around the lens barrel):
Befor removing the black part we should mark it to allow proper re-assembling:
Part removed:
Now, finally, we have access to focusing threads! But before separating them we want to remove the rear set of two lenses:
Beautiful fungus also here, on all surfaces ...
Now extract these four screws and remove the two copper guides:
Unscrew the two parts of the focusing mechanism and mark the position weher they separate:
Finally there's another ring to unscrew - before doings so, measure the correct thickness (= position):
These are the parts of the Pentax A 1.4/50mm. Not yet dismantled: the optical front group and the rear lenses (yellow arrows). The red arrow shows the rear negative doublet which should not be separated, of course, but just cleaned properly.
Next step: dismantling and cleaning of the front and rear optical groups! _________________ www.artaphot.ch |
|
| Haut de page |
|
 |
stevemark
 Inscrit le: 29 Avr 2011 Messages: 5509 Localisation: Switzerland
|
|
| Haut de page |
|
 |
stevemark
 Inscrit le: 29 Avr 2011 Messages: 5509 Localisation: Switzerland
|
 Posté: Jeu Avr 02, 2026 9:44 pm Sujet du message: |
|
 Posté: Jeu Avr 02, 2026 9:44 pm Sujet du message: |
|
|
stevemark wrote:
PART III: CLEANING THE REAR LENS GROUP
The rear lens group consists of four lenses in three groups [4/3]. The doublet directly behind the aperture comes out easily:
The last two lenses - two positive single lenses made of highly refractive lanthanum glass - are sealed in aas well. After soaking in acteone fr hours, unscrewing still was very difficult. I had to use "real gear" - not only a pincer, but a real pipe wrench! - to open this group. Of course one has to be VERY careful when using such tools on a lens ...!!
The two rear lenses are freed and now can be cleaned:
S _________________ www.artaphot.ch |
|
| Haut de page |
|
 |
stevemark
 Inscrit le: 29 Avr 2011 Messages: 5509 Localisation: Switzerland
|
 Posté: Mer Mai 20, 2026 7:55 pm Sujet du message: |
|
 Posté: Mer Mai 20, 2026 7:55 pm Sujet du message: |
|
|
stevemark wrote:
I completely forgot to show the cleaned and re-lubed lens (here on a Pentax LX with motor drive):
S _________________ www.artaphot.ch |
|
| Haut de page |
|
 |
|
|
|
Vous ne pouvez pas publier de nouveaux sujets dans ce forum Vous ne pouvez pas répondre aux sujets de ce forum Vous ne pouvez pas modifier vos messages dans ce forum Vous ne pouvez pas supprimer vos messages dans ce forum Vous ne pouvez pas voter dans les sondages de ce forum
|