MFlenses - Une nouvelle vie à l’ère numérique
MFLenses 2026

Forum des objectifs à mise au point manuelle

Explorez le monde des objectifs anciens à travers des notes de réparation, des photos d’essai réelles et des archives détaillées.

Explorez le monde des objectifs anciens à travers des notes de réparation, des photos d’essai réelles et des archives détaillées.
Pleins feux

Emplacement partenaire mis en avant sur la page d’accueil du forum.

Spring clean my body
Voir le sujet précédent :: Voir le sujet suivant  


Reply

Shocked

I would like to give my OM1n a spring clean (the outside of the body) and I'm wondering what is the best thing to use...?

Obviously, I am well aware of the danger of liquid entering the workings via the film wind lever and rewind lever etc.

Thanks for any advice Smile


Reply

Hi OM and welcome. I don't think you can clean off the grime properly without some kind of liquid. I use a cotton wool bud and lighter fuel, which dissolves the grease and it evaporates quickly. For the tightest corners I use a very small brush, like a toothbrush but smaller.


Reply

Thanks for that Peter.

I have a tin of Ronsonol lighter fluid - is that the stuff...?

I want to be sure so I don't damage the finish or any of the plastic bits like the viewfinder surround.


Reply

OM a écrit:
Shocked

I would like to give my OM1n a spring clean (the outside of the body) and I'm wondering what is the best thing to use...?

Obviously, I am well aware of the danger of liquid entering the workings via the film wind lever and rewind lever etc.

Thanks for any advice Smile


For the outside I use silicon polish......the one in a spray can, of course you don't spray the camera but the cloth then use it.


Reply

OM a écrit:
I have a tin of Ronsonol lighter fluid - is that the stuff...?

Yep, I have a tin of "Swan" lighter fluid.

You only need a small amount on the end of the Q-tip and keep changing the stick. If you try it on a piece of glass you'll see that a dirty tip leaves a residue film and to get it perfectly clean you need to make repeated passes using clean tips each time.

I've never found it causes any damage to plastic parts but it depends on the chemical composition I suppose. Try it on a small inconspicuous area if you have any doubt. It certainly affects the mirror bumper and light sealing foam round the door edges, so keep it away from these areas.

PS Don't use this method on lenses, mirrors or focussing screens!


Reply

I don't believe I would ever have told a customer but...erm...

Saliva on a toothbrush. Safe on just about any surface, it's commonly used by restorers in museums. The preferred method in fact. Honest.

Spit on the toothbrush, not the camera. Not too much!

Buff up with microfibre cloth, cut Q-tip sticks to shape to push the cloth into those awkward corners.

So next time your camera comes back from the repairer looking pristine...


Reply

unclemack a écrit:
I don't believe I would ever have told a customer but...erm...

Saliva on a toothbrush. Safe on just about any surface, it's commonly used by restorers in museums. The preferred method in fact. Honest.

Spit on the toothbrush, not the camera. Not too much!

Buff up with microfibre cloth, cut Q-tip sticks to shape to push the cloth into those awkward corners.

So next time your camera comes back from the repairer looking pristine...


..and a good hot vindaloo helps before spitting on the brush...... Smile


Reply

Saliva - I've heard that can be effective for lenses too though I wouldn't try it on a Zeiss or Leica Shocked

It's all to do with enzymes which help to break down the gunge allowing it to be wiped away.

I will try the lighter fluid/Q-tip idea and report back.

Thanks for the suggestions Smile


Reply

I'm just getting round to making a start - been under pressure with work but hey, the weather's rubbish anyway Smile

One more quick check - is it OK to use lighter fluid on the film guides and pressure plate...?

Many thanks


Reply

What's wrong with lighter fluid on camera mirrors or lens glass?

I would never use Swan lighter fluid on anything as it is not recommended for use in lighters.


Reply

I have Ronsonol lighter fluid - please tell me it is suitable...?


Reply

OM a écrit:
I have Ronsonol lighter fluid - please tell me it is suitable...?


That's what I have as well and use it on my lenses.


Reply

Great thanks Very Happy


Reply

It may be a myth, but Swan lighter fluid is supposed to destry lighters over a time. A tobacconist store has also told me this tale so I won't use it. I usually use Zippo fluid (as that's what they stock).


Reply

I use an optic cleaning cloth, swabs and sensor cleaning fluid. Dissolves grease and dirt and evaporates without leaving traces.


Reply

Thanks Vilhelm

Any particular sensor cleaning fluid...?

I thought that lighter fluid evaporates too...?


Reply

Lighter fluid evaporates yes, but at least the Zippo and Ronsonol brands I have in my shelf leave leave a greasy surface. Perhaps it does not matter.

Since you are cleaning the external of the camera, I doubt it differs what sensor cleaning fluid you are using. I used the cheapest I could find, saving the more expensive E2 for cleaning the low pass filter of the sensor. Sensor cleaning fluid evaporates real fast.


Reply

I agree with Vilhelm. Lighter fluid is fine for cleaning grubby metal and leatherette surfaces but it does leave an oily film on glass. For mirrors and focussing screens I use Eclipse lens fluid which you can buy on Ebay. There are two types - one for glass and one for sensors. I cut a small strip of PecPad microfibre cloth about 1cm wide, roll it up and fold in half, and hold it with tweezers. With one drop of fluid on it I can keep re-rolling and folding to use a clean part each time. How's that for meanness? It's a great way to clean Pentax focussing screens, including foam smears.

Martin, I've never once used Swan lighter fluid in a lighter! Smile My main use for it is cleaning sticky masking tape and photo-mount spray off my drawing board. It says on the tin it's a "Petrol Distillate, NOS" and "Extra refined, use in all lighter brands, cleaner burning, non-toxic. For spot cleaning grease marks on paper and cloth, removing sticky labels, removing tar spots etc. Test on a hidden area first." What's more, it's made here in High Wycombe! Smile