MFlenses - Une nouvelle vie à l’ère numérique
MFLenses 2026

Forum des objectifs à mise au point manuelle

Explorez le monde des objectifs anciens à travers des notes de réparation, des photos d’essai réelles et des archives détaillées.

Explorez le monde des objectifs anciens à travers des notes de réparation, des photos d’essai réelles et des archives détaillées.
Pleins feux

Emplacement partenaire mis en avant sur la page d’accueil du forum.

Bought two old studio flashes (+ question)
Voir le sujet précédent :: Voir le sujet suivant  


Reply

...and they work well! Both are of the Courtenay brand (Courtenay Solaflash 1000 and 8000). The 8000 is equipped with a slave sensor and its output can be changed (100%, 50% and 25%). Looks like overkill, but I wanted them to photograph my gear at low ISO and very small f/stops, even when the flashes are 2m away (I like the working distance as I'm clumsy).

They came complete with sturdy tripods and even the umbrellas (which I'm going to replace).

Of course, such a set is not without problems. While they work perfectly when connecting to any old camera with a X-sync, my Pentax K-7 (with PC connector) does not trigger the flashes. Apparently the K-7 is very picky in that regard. Would my problem probably be solved with this wireless set (which has a jack plug to fit into the studio flash): http://www.gadgetinfinity.com/product.php?productid=16656&cat=0&page=1 ?



Reply

Read the K7 manual as sometimes you have to set some functions to allow the PC socket to transmit a signal. In the 5dmkII you have to set liveview in a particular mode for example, otherway NADA Very Happy

Another test you can do is to use the K7 little flash at very low output to trigger the studio flashes putting them both in slave mode.


Reply

A G Photography a écrit:
Read the K7 manual as sometimes you have to set some functions to allow the PC socket to transmit a signal. In the 5dmkII you have to set liveview in a particular mode for example, otherway NADA Very Happy


Only PC sync in live view? How strange! Smile

There are no specific settings in the K-7 that are related to the flash, but I'll look a little more into it.

Citation:

Another test you can do is to use the K7 little flash at very low output to trigger the studio flashes putting them both in slave mode.


That doesn't work, thanks to the dreaded P-TTL flash mode (preflash) of the internal flash. It works when I use an old Pentax TTL-flash however. But for my intended use it's not handy to use a separate flash on the hot shoe. So I'm thinking about a better solution.


Reply

Spotmatic a écrit:
A G Photography a écrit:
Read the K7 manual as sometimes you have to set some functions to allow the PC socket to transmit a signal. In the 5dmkII you have to set liveview in a particular mode for example, otherway NADA Very Happy


Only PC sync in live view? How strange! Smile



Actually it doesn't even trigger hot-shoe flashes with live view-silent shooting in mode 1 or 2, it must be disabled.


Reply

I wouldn't connect my DSLR to old flashes without knowing their voltage ... You could fry your K7 doing so.

Use a multimeter to determine the exact voltage of the flashes. Most remote triggers can't handle high voltage either.

As a rule of thumb, I never mount a flash whose voltage is above 12 volts on my K200.

Use a Wein SafeSync to safely connect your flash to you DSLR (or google "DIY Safesync" if you're handy with electronics)


Reply

Thanks Jieffe. I don't worry that much about the trigger flash voltage; the K-7 should be able to handle 25 volts easily (on the PC contact). The measured voltages of those Courtenays are 15 and 20v, so it should be possible).


Reply

The problem I encountered sometimes with old flashes (and God knows I gathered a lot of these Rolling Eyes) is reversed polarity.

Some flashguns wouldn't fire on my DSLR (or remote trigger) until I opened the shoe and inverted the wires. Worth a try.


Reply

Yes, I have read the same things about the Courtenays and other old flash heads, but have not actually tried it yet (inverting the wires) because I also have seen messages that this does not make a difference on the K-7:

http://www.pentaxuser.co.uk/forum/topic/x-sync-socket-problem-16048/p-1#comm185063

Let's see if it helps!


Reply

I purchased from the same gadgetinfinity.com a Cactus 4.
That was 2 weeks ago. I haven`t had a chance to use it because my house is upside down due to some renovation work( which is driving me crazy).
Hopefully next week I`ll give it a try.


Reply

A friend of mine added some electronic parts in the smaller Courtenay. It now triggers perfectly! It also appeared that during triggering the flash sent +200 volts to the camera... Fortunately the Pentax K-7 seems to be well protected to such power surges... And yes, the polarity had to be reversed too.

I really like how my photos look exactly like studio shots now! Wink