MFlenses - Une nouvelle vie à l’ère numérique
MFLenses 2026

Forum des objectifs à mise au point manuelle

Explorez le monde des objectifs anciens à travers des notes de réparation, des photos d’essai réelles et des archives détaillées.

Explorez le monde des objectifs anciens à travers des notes de réparation, des photos d’essai réelles et des archives détaillées.
Pleins feux

Emplacement partenaire mis en avant sur la page d’accueil du forum.

Recycling silver from unwanted film and used fixer bath.
Voir le sujet précédent :: Voir le sujet suivant  


Reply

Do you have any experience with that?

I had the idea to recycle some silver some months ago.
So I collected some liters of used fixer bath (mostly from film, but I also "fixed"/extracted some old accidentially fractional exposed paper sheets with it before the procedure) and some extract I made from some sheets of old devoloped xray film (extraction solvent was a little H2O2, thinned H2SO4 and a little iron sulphate)

Short description of what I did with the (little excursion in chemistry):
First the solution (of both fixer and xray film extract) was filtered and then boiled down until some salts began to precipitate.
Then I added ~150ml hot saturated ascobic acid solution (Vitamin C solution, Glucose or electrolysis will also work instead) and brought the solution to boil (spends the Ag+ in the solution a missing electron to become insouble elemental Ag0).
Dark grey and very fine elemantal silver begins to precipitate (does not look like silver at all Very Happy)
I added some more water to redissolve some precipitated salts (at this point it won't harm the yield)
Then I washed the precipitate several time with hot water, filtered it, dried it.
Than I put the dark grey powder into a crucilbe (all ceramics should work) which was put into a gaphit powder bath (or active charcoal, sold as lubricant powder, water cleaning filters, gas mask filters,...) on some dishes to isolate it (sand and air are also very good) and put it for 7min @ 750W in a household microwave.
Here's a video I made:
http://youtu.be/K9jjboVZH7w
(graphit absorbs any microwave radiation and tansform it very effectivly into heat)
simpliefied diagram for the melting procedure in the microwave



After cooling down here's the result of several hours of work (made a lot of fun though Wink):

I have no scale here to tell how much it is but I will collect more Smile
Hopefully I will have enough to make a ring from it soon Very Happy

Do you have any own experience with the recycling of silver?
Has anyone tried to extract silver from film (should be also quite easy)?
I've seen some comercial silver precipitation agents in an online photo store so I guess I'm not the only one who tried this at home Smile


Dernière modification par ForenSeil le Lun Mar 12, 2012 1:50 am ; modifié 3 fois au total


Reply

Bravo!

Is procedure safe for average person not trained with chemical safety protocols? I worry that boiling fixer produces noxious fumes that any chemist would know special ventilation procedures are necessary, while average person would not know it. I think any potentially dangerous procedure should have a safety warning.


Reply

visualopsins a écrit:
Bravo!

Is procedure safe for average person not trained with chemical safety protocols? I worry that boiling fixer produces noxious fumes that any chemist would know special ventilation procedures are necessary, while average person would not know it. I think any potentially dangerous procedure should have a safety warning.

Well, I did it in my kitchen at home and the chemicals used are all absolutely unpiosonous (but should be used with care anyway in high concentations).
So yes it should be doable for everyone who's also able to devolope film on it's own.
The most dangerous step is definately the melting of the silver, which is hot enough to make very very serious burns even through clothes (by the way cotton protects much better than wool or synthetic textiles), or if overdone or not isolated good enough may overheat your microwave.

And I'm sure that there are much more easier ways than mine.
Ascorbic acid and glucose are weak reductants... I boiled the solution down because I thought that will produce a better yield. I guess a comercial or other silver reducer are stronger and will work very well even in very thinned silver solution.
I guess sodium dithionite (available at least here in evey drugstore and most supermarkers as bleach and/or stain remover in powedered form) will work much better than asorbic acid and glucose even in thinned solutions, but I've not testet it though.

Basically there are only these steps to get silver from used fixer or other silver containing solution:

1) Filter the solution (used fixer etc) to remove dust and dirt.
2) Add excess of reductant, dissolved in a little hot water (ascorbic acid or comercial reductant or maybe sodium dithionite are working fine) and wait or heat a little (to complete reaction)
3) Filter silver sludge
4) Wash silver sludge several time with hot water (to remove salts from fixer and excess of the reductant)
5) Let the silver sludgy unshiny silver powder dry (looks grey or black)
6) Melt the powder to nuggets etc. (with micowave/graphite method or with welding equipment etc.)