MFlenses - Une nouvelle vie à l’ère numérique
MFLenses 2026

Forum des objectifs à mise au point manuelle

Explorez le monde des objectifs anciens à travers des notes de réparation, des photos d’essai réelles et des archives détaillées.

Explorez le monde des objectifs anciens à travers des notes de réparation, des photos d’essai réelles et des archives détaillées.
Pleins feux

Emplacement partenaire mis en avant sur la page d’accueil du forum.

Mains cables for Bowens Monolites?
Voir le sujet précédent :: Voir le sujet suivant  


Reply

Where can you get them? old 1980's or 1970's lites have a 3 pin plug. I had some years ago and there are a couple going cheap. the socket looks like this and my drawing of the plug.



edit: plug is nothing like it. I remember it had 3 hollow pins


Dernière modification par philslizzy le Mar Nov 26, 2013 8:03 pm ; modifié 1 fois au total


Reply

what diameter is it Phil ? I think there's a box of old plugs at the back of my shed. It's probably easier to change the plug and socket to the kettle / PC power lead type. Everyone's got spare leads lying around for those.


Reply

I'm thinking that but it could be a costly investment if I cant. The plug appears to be a bulgin 3-pin type. Unfortunately I dont have the lights with me so I cant tell you the diameter.

This is the type of light and a better picture of the socket.




The plug pins appear to be hollow with contacts inside. I hoped it may be a Bulgin type but cant find anything online. There appears to be a stylised 'B' at the bottom of the socket. That probably is a Bowens mark, rather than Bulgin.


Reply

Get 'messin' Phil, the chances of finding those old leads are pretty poor. If you change them for 'kettle sockets' then new ready made leads are easy to find, as are extensions with the right plug and sockets.
Use a big fused one like this -

http://www.ebay.co.uk/itm/Fused-IEC-Chassis-Mains-Kettle-Socket-/300959366179?pt=UK_BOI_Electrical_Components_Supplies_ET&hash=item4612937c23

and you will probably be able to modify the existing hole, the smaller unfused ones might need a bit of thin metal plate to cover the oversize hole.


Reply

Is this any good, but the pin spacing is equal.

http://www.ebay.co.uk/itm/Bulgin-3-Pin-Cable-Line-Socket-Female-PX0430-SE-250Vac-1-5A-Fits-PX0429-2610-/141100800814

or mod it to this:-
http://www.adverts.ie/camera-accessories/bowens-monolite-400-e/255083


Reply

Excalibur a écrit:
Is this any good, but the pin spacing is equal.

http://www.ebay.co.uk/itm/Bulgin-3-Pin-Cable-Line-Socket-Female-PX0430-SE-250Vac-1-5A-Fits-PX0429-2610-/141100800814

or mod it to this:-
http://www.adverts.ie/camera-accessories/bowens-monolite-400-e/255083


I dont think so. I may just take the plunge and buy. Perhaps I can adapt.


Reply

I have a couple of the SAME FLASHES but I need the mains leads! I have an address for BOWENS and another flash repairer here in England : Bowens 355 old Road CLACTON C015 3RH Tel : 01255 422807
OR Denis Willing 01223 845205 ( Great Sheldon, Cambridgeshire) Hope these are still 'LIVE' contacts regards -- Peter


Reply

In case you have to re-plug it, would this schematics be of assistance?
http://static.photo.net/attachments/bboard/00V/00VsuN-224683584.jpg


Reply

pentaxpete a écrit:
I have a couple of the SAME FLASHES but I need the mains leads! I have an address for BOWENS and another flash repairer here in England : Bowens 355 old Road CLACTON C015 3RH Tel : 01255 422807
OR Denis Willing 01223 845205 ( Great Sheldon, Cambridgeshire) Hope these are still 'LIVE' contacts regards -- Peter


Hi Pete I'lll give it a go tomorrow and let you know. Cheers

twinquartz a écrit:
In case you have to re-plug it, would this schematics be of assistance?
http://static.photo.net/attachments/bboard/00V/00VsuN-224683584.jpg


Perhaps not, in this case, I will print it out though in case I need to make incursions!


Reply

Here you go...


http://bulgin.co.uk/Products/GenPurpose_Connectors/GenPurpose_Connectors.html

edit.
Actually no; there's a keyway in this one, which is likely an updated 'safer' version of yours. At the very least it gives you a choice of replacing the plug+socket with a modern type that looks just like the old one and retains originality/size instead of butchering the front panel for an IEC connector.


Reply

I got excited for a moment then I wondered why the keyway. I remember you could only put the plug in one way on the bowens - heres why:



left: Bowens right: Bulgin


Reply

Farside a écrit:
Here you go...


http://bulgin.co.uk/Products/GenPurpose_Connectors/GenPurpose_Connectors.html

edit.
Actually no; there's a keyway in this one, which is likely an updated 'safer' version of yours. At the very least it gives you a choice of replacing the plug+socket with a modern type that looks just like the old one and retains originality/size instead of butchering the front panel for an IEC connector.


That must be the most stupid plug to connect from a 230v mains supply......the person who designed that was an idiot Rolling Eyes


Reply

What I often do in these situations is simply add flylead with an inline socket on it, in this case, do away with the hard-to-find Bulgin entirely and use an IEC flylead socket.
It's always possible to make a safe cable exit from the equipment, using grommets and cable relief/grippers from the many dozens lying around in sparks' workshops.


Reply

The flylead was the final option - but as the lights are no no longer available this is all rather academic.

Thanks all of you for your input.

I will search for old ones now knowing I can use them.