MFlenses - Une nouvelle vie à l’ère numérique
MFLenses 2026

Forum des objectifs à mise au point manuelle

Explorez le monde des objectifs anciens à travers des notes de réparation, des photos d’essai réelles et des archives détaillées.

Explorez le monde des objectifs anciens à travers des notes de réparation, des photos d’essai réelles et des archives détaillées.
Pleins feux

Emplacement partenaire mis en avant sur la page d’accueil du forum.

Soligor 180mm 3.5 loose mount .... FIXED
Voir le sujet précédent :: Voir le sujet suivant  


Reply

i have just acquired this lens, its the chrome eared version 8xxx serial. problems: loose mount section, oily blades. Not clear how to disassemble this one. so far by loosening the grub screws on the focus ring I have managed to lose infinity focus... Sad
There is another screw that I think provides access to a screw under the focus ring. No screws at the mount end.

Any ideas?


Dernière modification par marcusBMG le Mer Oct 29, 2014 5:39 pm ; modifié 2 fois au total


Reply

I think I have the same lens and same looseness problem. That one is missing the T-adapter, right?


Reply

Yes I left off the t-mount for the pic.
Looking at the mount end there is a ring with two small holes in that look like they are for a custom spanner. It looks a bit like a bearing housing .. ??


Reply

Looseness between lens sections, including the mount, is something that's plagued me in the past. Sorry, I've no fix. I did post on this a while back, here:

http://forum.mflenses.com/broken-back-lenses-t65367,highlight,%2Bbroken+%2Bback.html

Doubt there's any help for you there. But you might want to read the thread anyway, just on background.


Reply

I have now figured out:
1. fully extend the lens
2. loosen/remove the 3 grub screws on the focus sleeve and the sleeve can be pushed up exposing the three yellow screws one of which is circled in red.

Tightening these screws should fix the loose mount kansalliskala, guardian. Now I have to figure out how to separate the helicoid to clean it and the iris. There is leaking gunk all around the iris housing.



Dernière modification par marcusBMG le Mer Oct 29, 2014 2:54 pm ; modifié 1 fois au total


Reply

Here is outline is how to fix a loose mount and access the iris on this soligor.

1. There are no screws on the mount end. There is instead a collar that needs a needle pointed lens spanner to unscrew. However unless there is a problem with the aperture rings there is no need to start disassembling the mount - it detaches as a unit.

2. To do so, locate the grub screw on the lens barrel above the focus sleeve, loosen it and now the front end of the lens can be unscrewed and separated. Note: may take some oomph to get started. Now loosen/remove the 3 grub screws on the focus sleeve, and a larger stop screw. The sleeve can now be slid up and off. The mount end is attached with 3 brass slotted screws. It is normally these screws that are loose if the mount is wobbly. Remove these and detach the mount.

3. To separate the helicoid, two wee guide rails are located in two slots. Remove these - 2 screws per rail. The helicoid can now be unscrewed completely. To clean the iris I removed the rear element and douched the whole assembly in solvent.

4. Reassembly is a simple reversal. To re-engage the helicoid I used the guide rail positions to align it, lining up with the slots. Resetting infinity focus was no problem.


Reply

Fixing the loose mount went well, Thanks. Mine isn't a T-mount Just M42 attached with three grub screws, no T-thread under there.


Reply

D1N0 a écrit:
Fixing the loose mount went well, Thanks. Mine isn't a T-mount Just M42 attached with three grub screws, no T-thread under there.

That will be a T mount (or T1) T2 had the screw. Some soviet lenses have a T1 mount like the Tair FS 300mm