MFlenses - Une nouvelle vie à l’ère numérique
MFLenses 2026

Forum des objectifs à mise au point manuelle

Explorez le monde des objectifs anciens à travers des notes de réparation, des photos d’essai réelles et des archives détaillées.

Explorez le monde des objectifs anciens à travers des notes de réparation, des photos d’essai réelles et des archives détaillées.
Pleins feux

Emplacement partenaire mis en avant sur la page d’accueil du forum.

3D adapter?
Voir le sujet précédent :: Voir le sujet suivant  


Reply

Hi,

has anybody in this forum tried to 3D print a lens adapter? Do you think it is possible? I do not have a 3D printer, but if that is feasible I'd give it a try.

Thanks.


Reply

Pretty sure I have seen printed adapters here, I have a printed Lens cap on on a lens, it came with it from *bay.


Reply

Sure, it's been done many times by many people. You can buy such adapters on eBay as well as download some models for free and have them printed yourself. There are more creative DIY adapters like that, for example one where you fix the plastic adapter onto tripod and rotate the camera, take four shots at four different angles with a medium format lens, combine that like panorama and get a 6x6 style image instead of a crop (using most of the lens' image circle, getting thinner dof etc.). Not the most practical solution for every day needs and easy shooting, but all sorts of crazy ideas are possible when you print your own adapters, as long as you know how to design them or find designs created by others.


Reply

Your Search for "lens adapter" - 2,044 printable 3D Models -- https://www.yeggi.com/q/lens+adapter/

Citation:
Just click on the icons, download the file(s) and print them on your 3D printer


Reply

I'm not familiar with all the types of 3D printed lens adapters that are available, but personally I would stay clear from adapters with all-plastic printed bayonet fittings.

Plastic, in the long run, will not hold up well to the continuous stress applied by the bayonet tension springs in the camera, which means one day unexpectedly the lens will drop off the camera.

Plastic fatigues when subjected to stress, esp. at corner stress points such as the 90Ëš corner between the bayonet "fingers" and the cylindrical section, on the side subjected to tension. Plastic bayonet body caps frequently fail at that point after modest use, and they are engineered to be more loose-fitting than lenses and barely compress the bayonet springs. Now image the same plastic bayonet mount, but tight fitting for use with a lens compressing the bayonet springs, and with the added stress of a heavy lens hanging off it...

I don't know if they exist but a good 3-D printed adapter could be based on a metal lens reverse ring, or metal mounts scavenged from (cheap/broken) lenses/cameras/OEM extension tubes. That way you would end up with proper metal mounts with only a plastic spacer tube to be 3-D printed, incl. appropriate baffles etc.


Reply

Yes, it works fine.
I print them in PLA+ or ABS for temporary use
Nylon of resin printers will produce more durable adapters,


Reply

3D printed adapters certainly have limitations but it is a valid solution.
In general you can forget about using them for heavy tele or zoom lenses, if you value them.

I use them mostly for projector lenses and small ( light ) enlarger lenses as a means to mount them to a helicoid and am satisfied with the results.
Never had any of them broken. Even if that happen you just print another one or ask somebody who has a 3D printer.




#1


#2


Reply

My designs are printed with black PETG filament, less issues with heat afterwards, shrink is reduced that way. Mount parts preferably alu reverse Sony FE or Canon EF adapters. Alu 39mm-M42 thread bushes turned on 3D printed 39mm thread. All to reduce wear and to avoid plastic debris floating in the camera.

With one exception: 3D printed PETG sleeve that can be turned on a Minolta SR mount to make it into a Canon EF mount. Infinity calibration done on the lens itself to take out the 0.5mm difference in register distance.

EF mounts get a programmed EMF chip for IBIS and EXIF through the Metabones IV smart adapter. Black 3.0 paint in the adapters to reduce reflections.
https://www.dpreview.com/forums/thread/4436674


Reply

Ernst Dinkla a écrit:
My designs are printed with black PETG filament, less issues with heat afterwards, shrink is reduced that way. Mount parts preferably alu reverse Sony FE or Canon EF adapters. Alu 39mm-M42 thread bushes turned on 3D printed 39mm thread. All to reduce wear and to avoid plastic debris floating in the camera.

With one exception: 3D printed PETG sleeve that can be turned on a Minolta SR mount to make it into a Canon EF mount. Infinity calibration done on the lens itself to take out the 0.5mm difference in register distance.

EF mounts get a programmed EMF chip for IBIS and EXIF through the Metabones IV smart adapter. Black 3.0 paint in the adapters to reduce reflections.
https://www.dpreview.com/forums/thread/4436674


That is a very sensible approach Like 1 small . Reverse adapters are also a good starting point for DIY mount conversions.


Reply

I'm not able to print my own, but I did had a kind gent from a forum print an unusual one for me (to mount dumb MFT lenses on M42 helicoids).
It did the trick nicely.