MFlenses - Une nouvelle vie à l’ère numérique
MFLenses 2026

Forum des objectifs à mise au point manuelle

Explorez le monde des objectifs anciens à travers des notes de réparation, des photos d’essai réelles et des archives détaillées.

Explorez le monde des objectifs anciens à travers des notes de réparation, des photos d’essai réelles et des archives détaillées.
Pleins feux

Emplacement partenaire mis en avant sur la page d’accueil du forum.

REPAIR: Rolleiflex 2.8D: Blocked Shutter Release Button
Voir le sujet précédent :: Voir le sujet suivant  


Reply

This pretty nice looking Rolleiflex 2.8D (SN 1604188, camera on the right) was given to me because the shutter release button was completely jammed.



Here are a few images to show how the problem was solved.

To have access to the shutter release button, we must remove the front plate. It's hold in place by three slotted screws and an additional pin shaped screw. The three slotted screws are hidden under the black leather cover. I didn't remove the leather completely, though; after applying some acetone (to soften the glue), I took a small screwdriver to loosen and remove the leather only as necessary.

First screw:


Second screw (close to the shutter release button):


The third screw is hidden behind the lever of the flash connector.


Therefore we have to remove the lever first:



Now we can extract the corresponding screw:


The last of the four screws is NOT the slotted screw visible on the left side, but the pin shaped screw close to the "M" and "X" of the flash selector:


The extracted pin-screw:


Now we can remove the front plate - don't loose the three (slightly bigger and thicker) washers beneath the three slotted screws!


Be aware that there are two tiny washers beneath the pin-screw - don't loose them (they are between front plate and actual camera body):


These tiny washers are about 100 um (0.1mm) thick:


Here's the inner actuator arm of the shutter itself - it's a bit slow due to old grease, but it works, and it certainly isn't jammed. Application of a drop of acetone removes most of the old grease and dirt, and the actuator arm is movin freely again. Obvioulsy this one isn't the root cause of the blocked shutter mecanism:


This is the part of the shutter release button hidden under the front cover. It should engage with the above lever and activate the shutter, but it doesn't move at all.



Therefore I go back to the outside of the front plate, and I remove these two parts from the shutter release button:




The shutter release button now is hold in place only by this spring. Remove the button and leave the spring in place!


The shutter release button is removed now:



At this point I became stuck. The construction of the mechanical transmission didn't make sense, since there was a mechanism to turn the button (from the outside), but obvioulsy coupling the button to the inner actuator arm would prevent any rotational movement. Since the shutter release button was made from one solid peace of metal, I could'n figure out how the mechanism could / should work.

After some time I noticed a tiny strip of corrosion (maybe 0,3mm broad) in the middle part of the shutter release button. That seemed strange to me - corrosion usually happens where two parts meet, and not in the middle of ONE part! Then the insight came - this solid block obviously was composed of TWO parts indeed! I machined a kind of mold which would fit to the outer, larger rim, hoping that I could remove the inner part by applying a fair amount of pressure. It didn't work, even with lots of pressure and lots of penetrating oil ...

Finally I noticed that the inner part might have to rotate before it could move laterally - and bingo! that was the solution. Quite a bit of force was needed, but then finally the inner part started rotating ... and soon also some lateral movement was possible. Problem solved, finally !!


Reassembling didn't cause any problems, and now the shutter can be released again. The shutter itself is a bit slow (and so is the self-timer), and the apertures are a bit too small, but the camera works again. A thorough CLA certainly would be appropriate, but since its not my camera I can't decide that ...

S