MFlenses - Une nouvelle vie à l’ère numérique
MFLenses 2026

Forum des objectifs à mise au point manuelle

Explorez le monde des objectifs anciens à travers des notes de réparation, des photos d’essai réelles et des archives détaillées.

Explorez le monde des objectifs anciens à travers des notes de réparation, des photos d’essai réelles et des archives détaillées.
Pleins feux

Emplacement partenaire mis en avant sur la page d’accueil du forum.

Olympus XA fixed
Voir le sujet précédent :: Voir le sujet suivant  


Reply

Seeing so much noise on that wonderful MJU II, I recalled having a spare XA pending for fixes, so I wanted to compare.
After a careful cleaning, replacing the light seals and putting fresh silver´-oxide batteries, I drop in a 12 shot roll film. This time, Konica VX200 expired since 08/2003. Just to see if the camera had light leaks and the electronics were fine for measuring and shooting.
No time to develop and scan at home, so I relayed on the lab. Cheap scan.

The camera itself: The "dirty" looking of the surface is due to the loss of the decorative finishing. Quite usual on the XA series if used often.









And some samples:







The closest distance the lens can focus:



Some more samples:







Being expired film I think the results are promising.
Regards.
Jes.


Reply

Jesito a écrit:






Is this somewhere around roads C-31 C-32. I think I drove the smaller road in 2004 on our honeymoon, first I ever drove in Spain. From Barcelona airport to Sitges. Thought that the smaller road would be easier to drive. Bad choice! Road was full of heavy local traffic with average speed about 110km/h. Shocked


Reply

kansalliskala a écrit:

Is this somewhere around roads C-31 C-32. I think I drove the smaller road in 2004 on our honeymoon, first I ever drove in Spain. From Barcelona airport to Sitges. Thought that the smaller road would be easier to drive. Bad choice! Road was full of heavy local traffic with average speed about 110km/h. Shocked


Good eye!. It's just as you mention, both C-31 and C-32 merge at the tunnels entrance, the small road is the local C-245, a snakey narrow road that saves oneself for paying a toll of 5,36€ for 8Km highway...
I pass twice per day so it's a considerable saving at the end of the month, only takes 12 minutes more and is plenty of nice places where to stop to shot a picture. Wink

Nice to know you spent the honeymoon in my village Smile

Regards.
Jes.


Reply

Good results from that, Jes.
My XA is starting to show the same scabby appearance, I think it's a laquer coat or something similar.


Reply

Farside a écrit:
Good results from that, Jes.
My XA is starting to show the same scabby appearance, I think it's a laquer coat or something similar.


Thanks David. Do you know if there is any way of restoring it?. I'm afraid all my XAs share the same problem...

Regards.
Jes.


Reply

The Royal Navy visited Sitges a couple of hundred years ago:-
http://i304.photobucket.com/albums/nn172/chakrata/sitgescannon.jpg

I visited 2 years ago, to go to a wedding.

edit: Found a snap of the beach at Sitges, the wedding was in the pink church in the distance.
http://i304.photobucket.com/albums/nn172/chakrata/sitges.jpg


Reply

I thinks the appearance adds character.

It looks like it gives reasonable results.


Reply

Cool! I had an XA years ago. It was handy to keep in a shirt pocket. Once in Malawi, I arrived at the airport a few hours ahead of Prince Charles, but because I didn't have proper accreditation, they confiscated all my Nikon gear -- but they missed the XA in my pocket! I got some great photos with XA on that trip, should dig them out. (And two weeks later, I was able to pry my Nikon gear out of customs!)


Reply

Jesito a écrit:
Farside a écrit:
Good results from that, Jes.
My XA is starting to show the same scabby appearance, I think it's a laquer coat or something similar.


Thanks David. Do you know if there is any way of restoring it?. I'm afraid all my XAs share the same problem...

Regards.
Jes.

If it is a laquer, I'd be wary of using a solvent in case it attacks the plastic, so that leaves the option of sanding it off, which is quite do-able with fine grades that will leave a smooth enough surface with the finer finish grade. After that, it might be possible to re-coat it with laquer, but whether it's worth all that bother, it's up to you. Wink If I was doing it, I'd strip it down first anyway.


Reply

Farside a écrit:
... If I was doing it, I'd strip it down first anyway.


That it what I was afraid of... I've been able to remove most of the old lacquer with Isopropylic alcohol and a lot of patience...
No worth to disassembly the camera just for cosmetic issues.

Now I'm fixing the XA2 that is in much better external shape. Smile


Regards.
Jes.


Reply

Jesito a écrit:
I've been able to remove most of the old lacquer with Isopropylic alcohol and a lot of patience...

That's useful to know - and I have a bottle of that handy, too. The coating on mine seems to have started being eaten away by finger grease and acids - probably some careless moment years ago. Fish and chips and cameras don't go together Wink