MFlenses - Une nouvelle vie à l’ère numérique
MFLenses 2026

Forum des objectifs à mise au point manuelle

Explorez le monde des objectifs anciens à travers des notes de réparation, des photos d’essai réelles et des archives détaillées.

Explorez le monde des objectifs anciens à travers des notes de réparation, des photos d’essai réelles et des archives détaillées.
Pleins feux

Emplacement partenaire mis en avant sur la page d’accueil du forum.

PX 675 replacement
Voir le sujet précédent :: Voir le sujet suivant  


Reply

Hi
I am spending time and then more time to find replacement of the PX 675 battery that is not more sold.
This is 1.35volts and there are people commenting that using the more recent LR44 that are 1.5Volts would make the light meter to slightly change its behavior.

What should be a right replacement for me and which one should I select?

I would like to thank you in advance for your reply
Regards
Alex


Reply

In my Konica Autoreflex T3N camera, I use 2x 1.4V hearing aid batteries. They are very common and can be bought pretty much in any drug or big box store. I tested how much the 2x 0.05V difference throws the metering system off and I found it to be off by 1 1/3 stops. I just adjust the ASA to compensate for this. So if I am shooting ASA 400 film, I set the ASA to 160 and get perfectly exposed shots. The compensation may be slightly different for cameras that use only 1 battery. Read this thread for more detail:

http://forum.mflenses.com/konica-t3-metering-with-1-4v-batteries-t62814.html


Reply

I use LR44's in my Minolta and there is no difference that I can see in terms of results.


Reply

Hi,
I got for the weekend a sensored camera that gets the 1.35volt batteries. As I do not have a light meter I guess it would be easier to test the light meter against the f/16 rule to see how off it can be. Is that right?

Regards
A.


Reply

I use these to adapt LR44 batteries to PX625 cameras in my Canon F-1, Minolta SRT 101, Nikkormat FTN, and others.

http://www.ebay.com/itm/Battery-Adapter-for-A76-LR44-Cell-Battery-to-625-Camera-Cell-Button-/140787331021?pt=Batteries_Chargers&hash=item20c7942fcd

You can also use PX625 but the increased voltage will cause the light meters to underexpose two stops (give or take.) So you need to compensate with the ISO dial (ISO 400 film would be shot with the dial set to ISO 100.) The easiest way to ascertain your compensation is to use the Sunny 16 rule. Set the aperture at f16 and your shutter speed at the nearest speed to your ISO. Then adjust the ISO dial until you have a centered reading.

However, for $4, those little adapter are great. I bought nine just in case I lose some (I already lost one.)


Reply

Hi
I bought today those LR44 which are 1,5volts.
The light meter did not responded... I am not sure if is the battery or is once more a broken light meter Sad

A.


Reply

Hi few more questions for the club experts
I have put some carton to make the LR44 battery to fit nicely in the slot, as I do not have any sun around I have turned asa setting to 1600 and had my camera very close to my laptops brightness but I can not see the needle moving..
I only see a very small movement of the lens when I am switching the switch from the off to the on state regardless if there is battery or not.
According to what I found on the internet LR44 can be of course used but light meter might drift a bit but currently I see no movement at all.

Do you have any suggestions how I should proceed now?

Alex


Reply

The LR44 and PX batteries are different thcknesses as well as different diameters. So the camera may not be making reliable contact.


Reply

thanks for the answer
please confirm me the following
iso 800 and iso 1600 should make the needle to move high or down even with home ligthing (going really close to a light bulb)

A


Reply

Depends on the aperture and shutter speed. A knee-jerk guess, setting the ISO at 1600 and pointing the lens at a lightbulb, then the needle ought to start way up at the plus and move downward to the minus as you stop the lens down. If you have a smartphone, download one of the free light meter apps and check your camera against it. The readings ought to be within 1 to 1.5 stops.


Reply

does not move Sad
I will order a better fit battery but I am pretty sure that light meter does not work on that camera either Sad